AZ Window Services LLC

AZ Window Services LLC Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from AZ Window Services LLC, Home window service, 1761 West University Drive #143, Tempe, AZ.
(225)

09/08/2026

Upgrading old or degraded window film requires thorough surface prep and precise installation to achieve a seamless, professional finish.

To start, strip away the old tint and scrape off remaining adhesive residue with a lubricated razor blade to prevent scratching the pane. Once the glass is completely spotless, generously spray the surface with a slip solution—usually mild soapy water—and carefully align the new window tint sheet against the top edge. Smooth the film down onto the wet glass, adjusting its position as needed, then use a squeegee to push out trapped water and air bubbles from the center outward. Finally, trim any excess film around the edges for a clean fit, wipe down the frame, and allow the adhesive to fully cure.

Follow for more!

09/08/2026

Removing old window film residue requires proper tools and continuous lubrication to slice through adhesive without scratching the glass.

To begin, generously spray a soapy water mixture onto the glass surface to lower friction and ensure the razor blade glides smoothly. Next, hold a flat glass scraper or razor blade at a shallow angle—roughly 30 to 45 degrees—and push forward using steady, controlled strokes to peel up the gunk. As you work, frequently clear the gathered adhesive off the scraper blade with a towel so you don’t drag residual adhesive back across the glass. Once all the film residue is lifted, apply a final spray of adhesive remover or standard glass cleaner and squeegee or wipe the window down for a completely streak-free finish.

Follow for more!

09/08/2026

Why razor glass before squeegeeing?
⠀
Construction debris, paint overspray, and hard water buildup bond to glass surfaces. A soapy solution lubricates the blade so it floats across the glass, lifting stuck material without scratching the pane. Following up with a clean squeegee pass leaves a streak-free finish that standard washing cannot match.
⠀
Follow for more.
⠀

09/04/2026

Installing window tint on a set of bay or multi-pane windows drastically reduces indoor heat while keeping natural light flowing into the room.
To achieve a clean installation, start by thoroughly spraying and squeegeeing the glass to eliminate all dust and surface debris. Measure and pre-cut each film panel to size before spraying the window with slip solution. Carefully position the film onto the glass, pressing it flat against the pane and using a firm squeegee to push out any trapped water and air bubbles from the center outward. Finish by trimming any excess film along the edges for a flush fit that keeps your space cooler and protected from UV rays.

Follow for more!

installation

09/04/2026

Window tint percentage, or Visible Light Transmission (VLT), measures the amount of natural light that can pass through the glass after film installation. A lower VLT number, such as 5%, blocks up to 95% of incoming light to provide maximum shade and privacy, while a higher VLT percentage like 35% allows significantly more natural light inside while still absorbing, blocking, and rejecting heat. Because the film actively absorbs solar energy, the glass surface itself warms up, preventing thermal heat from freely passing through into your living space.

Follow for more!

09/04/2026

Thinking windows reject heat before it enters?
⠀
Standard glass allows solar heat to pass directly into your living space, forcing your HVAC unit to work double time. Solar control window film reflects UV rays and infrared heat at the glass surface rather than letting it build up inside. Proper installation requires thorough glass cleaning, precise wet application, and edge squeegeeing to ensure an airtight bond.
⠀
Blocking heat at the glass layer saves energy and reduces indoor temperatures efficiently.
⠀
Follow for more.
⠀

09/04/2026

Precision tinting in action!

Applying solar window film requires serious skill to get those seamless, razor-sharp edges without scratching the glass or tearing the material. Thorough surface prep with squeegees and wetting solution prevents trapped dust and air bubbles.

Trimming directly along the window frame ensures an exact fit that maximizes heat rejection across the entire pane, while a smooth peel removes excess film for a flawless, factory-finish border.

Follow for more!

08/31/2026

How do you get instant bathroom privacy without blocking natural light? Traditional blinds collect dust and moisture, but a professional frosted window film application offers a clean, modern solution that keeps your space bright while completely obscuring the view from the outside.
⠀
The key to a flawless install lies in the preparation and sealing. After thoroughly cleaning the glass to remove every speck of dust, the film is carefully squeegeed to eliminate any trapped air bubbles. The final, crucial step is applying a clean bead of silicone caulk around the perimeter to lock out moisture and prevent the edges from peeling over time.
⠀
Follow for more home improvement tips and tricks.
⠀

Address

1761 West University Drive #143
Tempe, AZ
85281

Opening Hours

Monday 8am - 6pm
Tuesday 8am - 6pm
Wednesday 8am - 6pm
Thursday 8am - 6pm
Friday 8am - 6pm
Saturday 8am - 6pm

Telephone

+14804180647

Website

Alerts

Be the first to know and let us send you an email when AZ Window Services LLC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to AZ Window Services LLC:

Shortcuts

Share

Category