On Site Architect

On Site Architect Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from On Site Architect, Architectural Designer, United States, Los Angeles, CA.

🛠️ Satisfying renovations & master craftsmanship
🏗️ Giving a second life to spaces
🎬 Commenting on the best architectural crafts
📩 Business & Collab: [email protected]

08/18/2026

Stop relying on basic 45-degree cuts for your baseboard corners! 📐
Standard flat cuts ignore the depth and curves of the trim profile, which is why you always end up with ugly gaps. The pro secret is using a square to trace both vertical and horizontal angles together! Cut along those custom 3D lines, and watch the two pieces lock together seamlessly like a puzzle with zero gap!
Save this reel for your next DIY home project! Did you know about this profiling trick? Let me know in the comments below! 👇

08/18/2026

Stop measuring every single corner when building deck stairs! 🪵
The easiest trick is leaving the panel long and using a router tool to glide along the frame. It cuts off the excess instantly and leaves a perfectly flush edge every single time!
Save this reel for your next woodworking project! Have you ever used a router like this? Let me know below! 👇

08/18/2026

Say goodbye to roof leaks with traditional lead flashing! 🏠🔨
Forget cheap sealant tapes that peel off in winter. Malleable lead sheets molded directly over roof tiles with a wooden tool create a seamless, weatherproof barrier that lasts for generations!
Save this reel for your next building project! Do you prefer traditional lead or modern waterproofing tapes? Drop your thoughts below! 👇

08/17/2026

Stop cutting your wall trims in half! 📐
Mark a 45-degree angle, notch out the inner corner, and simply fold it over for a flawless, gap-free edge. It looks so clean and takes only seconds!
Save this reel for your next home project! What’s your go-to corner fitting method? Let me know in the comments! 👇

08/16/2026

Stop using tape measures for curved floor cuts! 📐
Measuring round borders and curved walls with a tape measure almost always leads to wrong cuts and wasted boards. The professional secret is placing the plank over the floor and tracing the contour directly with a small reference piece. Cut along your line for a rock-solid, zero-gap fit!
Save this reel for your next flooring project! Have you ever struggled with cutting curved edges? Drop a comment below! 👇

08/16/2026

Stop buying cheap foam moldings when you can build timeless architectural features with raw mortar! 🏛️
The magic lies in the custom wooden profile rule. Pulling it over wet cement layers instantly creates perfectly uniform curves. Once it slightly sets, fine hand trowels define the intricate flutes and crisp corners.
Save this reel for your next building project! Do you prefer modern minimal trims or classic detailed moldings? Let me know in the comments! 👇

08/15/2026

Stop cutting standard 45-degree angles for your corner trims! 📐
Almost no wall in a real house is a perfect 90 degrees, which is why your miter cuts always leave gaps. The pro trick is using a protractor rule to match the wall's actual angle, trace the overlap, and cut precisely along the line. Both pieces will snap together with absolute zero gap!
Save this reel for your next renovation project! Have you ever struggled with uneven wall corners? Let me know in the comments below! 👇

08/14/2026

Never replace old hardwood floors before trying this restoration trick! 🛠️
First, every nail is countersunk deep into the wood. Then, fine sawdust is blended with resin to create a filler that seamlessly hides every crack. After a smooth sanding session and a fresh coat of sealer, this historic floor looks better than brand-new timber!
Save this reel for your next home renovation project! Would you restore your original wooden floors or replace them with modern laminate? Drop your thoughts below! 👇

08/14/2026

90% of people make this mistake when fixing a roof leak in the rain! 🚫 That black stuff isn't regular silicone—it's heavy-duty polyurethane mast designed to stick to wet metal. But if you smooth it out with your fingers, you'll ruin the seal. Have you ever tried fixing a leak during a heavy storm? Drop your thoughts below!

08/13/2026

Never drive screws directly into wood when installing metal corner brackets! 🛠️
Screws alone often fail to get a deep grip on soft timber, causing your brackets and joints to wobble over time. The professional trick is placing a drop of wood glue and a small toothpick into the hole first. As you drive the screw in, it compresses the wood fibers against the metal bracket, creating an unbreakable, rock-solid lock!
Save this reel for your next woodworking project and tag a friend who needs this pro tip! Will you try this on your next build? Let me know in the comments! 👇

Address

United States
Los Angeles, CA
10001

Website

,

Alerts

Be the first to know and let us send you an email when On Site Architect posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to On Site Architect:

Shortcuts

Share

Category