LLumar Window Film Singapore

09/10/2026

04/10/2026

𝐇𝐨𝐰 𝐒𝐚𝐟𝐞𝐥𝐲 𝐂𝐚𝐧 𝐎𝐥𝐝 𝐂𝐚𝐫 𝐓𝐢𝐧𝐭 𝐁𝐞 𝐑𝐞𝐦𝐨𝐯𝐞𝐝?

After years of sun and repeated thermal cycling, does not always peel away neatly like a sticker.

The film may have become brittle.
The adhesive may have changed and can leave residue on the glass.
On the rear windscreen, the old may be bonded across delicate electrical lines that are part of the car itself.

For some older vehicles, film removal requires more judgement than installing new film.
This part deserves more attention.

𝐖𝐡𝐚𝐭 𝐆𝐨𝐨𝐝 𝐂𝐚𝐫 𝐓𝐢𝐧𝐭 𝐑𝐞𝐩𝐥𝐚𝐜𝐞𝐦𝐞𝐧𝐭 𝐋𝐨𝐨𝐤𝐬 𝐋𝐢𝐤𝐞

A quality replacement job should not simply be:
Peel old film → install new film.

It should be closer to:
Inspect → remove carefully → clean → inspect again → select appropriate film → install → finish → verify.

𝐑𝐞𝐩𝐥𝐚𝐜𝐞𝐦𝐞𝐧𝐭 𝐈𝐬 𝐚𝐧 𝐎𝐩𝐩𝐨𝐫𝐭𝐮𝐧𝐢𝐭𝐲 𝐭𝐨 𝐒𝐭𝐚𝐫𝐭 𝐀𝐠𝐚𝐢𝐧 𝐏𝐫𝐨𝐩𝐞𝐫𝐥𝐲

Once the old film has been safely removed and the glazing cleaned, the owner can reassess what is actually needed.

- Maybe the original tint was too dark or too reflective.
- Maybe the owner wants clearer visibility at night.
- Maybe the vehicle now spends more time outdoors than when the first film was installed.

This is the point at which film selection should restart from the actual requirement rather than simply copying what was there previously.

𝐀𝐭 𝐖𝐢𝐧𝐝𝐨𝐰-𝐂𝐨𝐨𝐥, 𝐖𝐞 𝐏𝐫𝐨𝐟𝐞𝐬𝐬𝐢𝐨𝐧𝐚𝐥𝐥𝐲 𝐆𝐮𝐢𝐝𝐞 𝐘𝐨𝐮𝐫 𝐅𝐢𝐥𝐦 𝐒𝐞𝐥𝐞𝐜𝐭𝐢𝐨𝐧

With over 25 years of market expertise, our team of in-house professionals will ensure that your new window film replacement will perfectly suit your car's current needs.
Contact us for a quote today!

☎️: 6288 8323 📱: 8288 8555
https://windowcool.s.gy/AutomotiveSolarFilms

30/09/2026

𝐓𝐡𝐞 𝐒𝐭𝐚𝐢𝐫𝐰𝐞𝐥𝐥: 𝐀 𝐂𝐨𝐦𝐦𝐨𝐧 𝐇𝐨𝐭 𝐒𝐩𝐨𝐭 𝐢𝐧 𝐋𝐚𝐧𝐝𝐞𝐝 𝐇𝐨𝐮𝐬𝐞𝐬

In many landed homes, the stairwell area beside windows often feels extremely hot.

This happens because hot air naturally rises upward.
As warm air accumulates in the stairwell, it becomes trapped near the upper floors, creating a heat pocket.

A trick to reduce this heat build-up is to open a small gap at the top section of the window, instead of keeping all glass panels tightly closed.

This allows the trapped hot air to escape naturally through the upper opening. As the hot air exits, cooler air from lower areas of the house slowly replaces it, creating natural airflow.

𝐒𝐨𝐥𝐚𝐫 𝐇𝐞𝐚𝐭 𝐓𝐡𝐫𝐨𝐮𝐠𝐡 𝐖𝐢𝐧𝐝𝐨𝐰𝐬

Windows are typically the largest source of heat entering a home.
When sunlight hits glass, the solar energy splits into three parts:

• Reflection – some heat is reflected away
• Transmission – some heat passes through the glass into the room
• Absorption – some heat is absorbed by the glass and later radiates inward

Clear glass allows a significant amount of solar energy to pass through. This is why rooms facing the sun often become very warm in the afternoon.

Installing professional solar-control can significantly reduce the amount of heat entry.
High-performance films reflect a large portion of the solar radiation before it even enters the room, helping to keep interiors cooler.

along with proper airflow and ventilation can help immensely in alleviating heat pocket problems in common stairways and households.

𝐂𝐨𝐧𝐭𝐚𝐜𝐭 𝐮𝐬 𝐟𝐨𝐫 𝐚 𝐅𝐑𝐄𝐄 𝐪𝐮𝐨𝐭𝐞:
☎: 6288 8323 | 📱: 9229 6008
https://windowcool.s.gy/home-solar-films

24/09/2026

𝐖𝐡𝐲 𝐢𝐬 𝐃𝐑𝐍𝟐𝟓𝐒𝐑𝐂𝐃𝐅 𝐒𝐨 𝐏𝐨𝐩𝐮𝐥𝐚𝐫 𝐢𝐧 𝐒𝐢𝐧𝐠𝐚𝐩𝐨𝐫𝐞?

When homeowners ask us which we install most often for HDB, condominiums, landed homes and offices, one model comes up again and again: DRN25.

Under Night Vision Series, DRN25SRCDF has become one of 's most recommended architectural films because it strikes a balance that many struggle to achieve:

✅Combining excellent daytime heat rejection with moderate daylight privacy
✅Clearer night-time views than traditional reflective films
✅A natural exterior appearance and long-term durability
✅Backed by independent fire testing

Rather than chasing extreme specifications or exaggerated infrared claims, DRN25 focuses on something more useful in practice: comfortable living every day.

That's why LLumar DRN25 has been on the top of our film model selections for the past 2 decades.

𝐂𝐨𝐧𝐭𝐚𝐜𝐭 𝐮𝐬 𝐟𝐨𝐫 𝐚 𝐅𝐑𝐄𝐄 𝐪𝐮𝐨𝐭𝐞:
☎: 6288 8323 | 📱: 8288 8555
https://windowcool.s.gy/DualReflectiveFilms

16/09/2026

𝐓𝐞𝐦𝐩𝐞𝐫𝐞𝐝 𝐆𝐥𝐚𝐬𝐬 𝐈𝐬 𝐒𝐭𝐫𝐨𝐧𝐠.
𝐒𝐨 𝐖𝐡𝐲 𝐃𝐨𝐞𝐬 𝐈𝐭 𝐒𝐭𝐢𝐥𝐥 𝐍𝐞𝐞𝐝 𝐒𝐚𝐟𝐞𝐭𝐲 𝐅𝐢𝐥𝐦?

Even if it's up to five times stronger than ordinary glass, tempered glass like your can still instantly from edge impacts.

When that happens, an entire pane can disintegrate within a fraction of a second, scattering thousands of small glass fragments across the surrounding area.

does not prevent from breaking.
Instead when the glass fails, the film holds the broken fragments together, reducing the risk of injury, helping to secure the opening, and minimising disruption until the damaged panel can be replaced.

This distinction explains why architects, facility managers, schools, hospitals, commercial buildings, and MCSTs throughout continue to specify safety and even where tempered glass has already been installed.

𝐂𝐨𝐧𝐭𝐚𝐜𝐭 𝐮𝐬 𝐭𝐨 𝐠𝐞𝐭 𝐚 𝐪𝐮𝐨𝐭𝐞 𝐨𝐫 𝐟𝐨𝐫 𝐦𝐨𝐫𝐞 𝐢𝐧𝐟𝐨:
☎️: 6288 8323 📱: 9229 6008
https://windowcool.s.gy/SafetyFilms

02/09/2026

𝐖𝐡𝐲 𝐒𝐨𝐦𝐞 𝐆𝐥𝐚𝐬𝐬 𝐈𝐧𝐬𝐭𝐚𝐥𝐥𝐚𝐭𝐢𝐨𝐧𝐬 𝐑𝐞𝐪𝐮𝐢𝐫𝐞 𝐄𝐱𝐭𝐞𝐫𝐢𝐨𝐫 𝐅𝐢𝐥𝐦 𝐀𝐩𝐩𝐥𝐢𝐜𝐚𝐭𝐢𝐨𝐧

In most buildings, solar control is installed on the interior side of the glass.
Interior installation protects the film from weather exposure and generally provides the longest lifespan.

However, certain glazing conditions — especially skylights, roof glass, and heavily sun-exposed structures require installation instead.
In these cases, installing film on the interior surface can create thermal stress, increase heat retention, and potentially damage the glass.

> 𝐒𝐤𝐲𝐥𝐢𝐠𝐡𝐭𝐬 𝐄𝐱𝐩𝐞𝐫𝐢𝐞𝐧𝐜𝐞 𝐄𝐱𝐭𝐫𝐞𝐦𝐞 𝐒𝐨𝐥𝐚𝐫 𝐇𝐞𝐚𝐭

Unlike vertical windows, roof glazing receives sunlight almost perpendicular to the glass surface, allowing a large amount of solar energy to enter the glass system.

When solar film is installed on the interior side of skylight glass, much of that solar energy is absorbed within the glass itself.

> 𝐈𝐧𝐭𝐞𝐫𝐢𝐨𝐫 𝐅𝐢𝐥𝐦 𝐨𝐧 𝐒𝐤𝐲𝐥𝐢𝐠𝐡𝐭𝐬 𝐂𝐚𝐧 𝐂𝐚𝐮𝐬𝐞 𝐓𝐡𝐞𝐫𝐦𝐚𝐥 𝐒𝐭𝐫𝐞𝐬𝐬

If solar control film is installed on the interior side:
1. Sunlight enters the glass.
2. Solar energy is absorbed by the film and glass.
3. Heat becomes trapped within the glazing system.

The center of the glass becomes very hot, while the edges remain cooler, developing thermal stress.

> 𝐖𝐡𝐲 𝐄𝐱𝐭𝐞𝐫𝐢𝐨𝐫 𝐅𝐢𝐥𝐦 𝐇𝐞𝐥𝐩𝐬

Interior film allows heat to enter the glass first, but exterior solar film stops a large portion of solar energy before it enters the glass — keeping the glass cooler and reducing the risk of cracking.

𝐂𝐨𝐧𝐭𝐚𝐜𝐭 𝐮𝐬 𝐭𝐨 𝐠𝐞𝐭 𝐚 𝐪𝐮𝐨𝐭𝐞 𝐨𝐫 𝐟𝐨𝐫 𝐦𝐨𝐫𝐞 𝐢𝐧𝐟𝐨:
☎️: 6288 8323 📱: 9229 6008
https://windowcool.s.gy/ExteriorFilms

26/08/2026

𝐈𝐑𝐑 𝐯𝐬 𝐈𝐑𝐄𝐑 𝐯𝐬 𝐓𝐒𝐄𝐑: 𝐇𝐨𝐰 𝐭𝐨 𝐂𝐨𝐦𝐩𝐚𝐫𝐞 𝐒𝐨𝐥𝐚𝐫 𝐅𝐢𝐥𝐦 𝐇𝐞𝐚𝐭 𝐑𝐞𝐣𝐞𝐜𝐭𝐢𝐨𝐧 𝐏𝐫𝐨𝐩𝐞𝐫𝐥𝐲

This is one of the most common sources of confusion when comparing automotive .

A film advertising 96% infrared rejection cannot automatically be considered better than another film showing 60% IRER, because the two percentages may represent different wavelength ranges, different measurement methods, and entirely different aspects of solar performance.

At , we believe the better way to compare films is not to search for the largest percentage, but to first understand what each percentage actually represents.

𝐈𝐑𝐑, 𝐈𝐑𝐄𝐑 𝐨𝐫 𝐓𝐒𝐄𝐑: 𝐖𝐡𝐢𝐜𝐡 𝐍𝐮𝐦𝐛𝐞𝐫 𝐒𝐡𝐨𝐮𝐥𝐝 𝐂𝐨𝐧𝐬𝐮𝐦𝐞𝐫𝐬 𝐓𝐫𝐮𝐬𝐭?

The better approach is not to choose one number and disregard the others, since each provides different information.

𝐈𝐑𝐑 can show infrared performance within a defined wavelength range.
𝐈𝐑𝐄𝐑 provides a broader view of infrared-energy performance.
𝐓𝐒𝐄𝐑 provides a broader measurement of overall total solar-energy rejection.
𝐕𝐋𝐓 tells you how much visible light remains.

Together, these figures provide a much clearer picture than any single headline percentage ever could on its own.

Now that you have an understanding of these terms, a better way to do it is to compare IRR vs. IRR between 2 brands, or TSER vs. TSER of different manufacturers for a more accurate and leveled performance overview.

𝐂𝐨𝐧𝐭𝐚𝐜𝐭 𝐮𝐬 𝐰𝐢𝐭𝐡 𝐲𝐨𝐮𝐫 𝐜𝐚𝐫 𝐦𝐨𝐝𝐞𝐥 𝐟𝐨𝐫 𝐚 𝐅𝐑𝐄𝐄 𝐪𝐮𝐨𝐭𝐞.
☎️: 6288 8323 📱: 8288 8555 https://windowcool.s.gy/AutomotiveSolarFilms

21/08/2026

𝐖𝐡𝐲 𝐋𝐋𝐮𝐦𝐚𝐫 𝐍𝐑𝐌𝟓𝟓𝐏𝐒𝟒 𝐆𝐥𝐚𝐜𝐢𝐞𝐫 𝐎𝐮𝐭𝐩𝐞𝐫𝐟𝐨𝐫𝐦𝐬 𝐒𝐭𝐚𝐧𝐝𝐚𝐫𝐝 𝐅𝐫𝐨𝐬𝐭𝐞𝐝 𝐅𝐢𝐥𝐦𝐬

Many on the market rely on PVC materials that are prone to shrinking, bubbling, or yellowing over time.

The Glacier uses non-PVC PET technology, offering superior resistance to heat, moisture, and UV exposure.

This makes it particularly suitable for HDB flats, condominiums, offices, and commercial buildings across .

In addition to , the built-in safety layer helps hold broken glass together upon impact, reducing the risk of injury and secondary damage — perfect for bathrooms and shower screen glass!

𝐊𝐞𝐲 𝐅𝐞𝐚𝐭𝐮𝐫𝐞𝐬 𝐨𝐟 𝐋𝐋𝐮𝐦𝐚𝐫 𝐍𝐑𝐌𝟓𝟓𝐏𝐒𝟒 𝐆𝐥𝐚𝐜𝐢𝐞𝐫:

• 4mil PET Safety Base
• Elegant Frosted Privacy Finish
• Up to 99% UV Rejection
• Excellent Heat Stability
• Non-PVC, Eco-Responsible Construction

⸻

𝐂𝐨𝐧𝐭𝐚𝐜𝐭 𝐮𝐬 𝐭𝐨 𝐠𝐞𝐭 𝐚 𝐪𝐮𝐨𝐭𝐞 𝐨𝐫 𝐟𝐨𝐫 𝐦𝐨𝐫𝐞 𝐢𝐧𝐟𝐨:
☎️: 6288 8323 📱: 9229 6008
https://windowcool.s.gy/SolarFrostedFilm