KC Artistic Concrete

KC Artistic Concrete Our goal is to provide you with a high quality concrete experience from start to finish. Serving Missouri/Kansas with-in 100 mile radius of Kansas City Mo.

Concrete Staining, epoxies, coatings, sealing, flatwork, stamped concrete, restain and seal. Driveways, porches, stoops, steps, garage floors, patios, screened in patios, BASEMENTS, pool decks, walk ways, basketball courts, anything concrete!! Residential/Commercial

07/18/2026

Myth — "If It Looks Fine on the Surface, It's Fine Underneath"

This one catches people off guard because it sounds reasonable, if there's no visible damage, there's no problem, right?

Not always. Moisture lives underneath concrete long before it shows up on the surface. Contamination from oils, sealers, and old adhesives can be invisible to the eye but completely compromise a coating's ability to bond. And concrete that feels solid underfoot can still have surface porosity issues that need to be addressed before any system goes down.

It's the reason we test and assess every slab before we coat it, not after. By the time a problem is visible on the surface, it's usually already done some damage underneath. Catching it in the estimate phase is always cheaper than dealing with it after install.

When we walk a job, we’re looking at more than square footage.We’re looking at the cracks, worn areas, staining, old coa...
07/17/2026

When we walk a job, we’re looking at more than square footage.

We’re looking at the cracks, worn areas, staining, old coatings, surface condition, and anything else that could affect the finished floor. Cracks can give us clues about movement in the slab. Discoloration may point to moisture, chemicals, or something that was previously applied. The condition of the concrete helps us determine what kind of prep it will need and whether the system you’re considering is the right fit.

We’re also looking at how the space is used, where water may enter or collect, and what kind of daily wear the floor will see. A garage, basement, commercial space, and exterior slab may all need a different approach, even when the concrete looks similar at first glance.

All of that gets figured out before we recommend a system or put a price on the job. Because putting the wrong coating over the wrong slab doesn’t solve the problem, it just makes the next repair more expensive.

After 19 years and more than 2 million square feet of concrete, we’ve learned that a floor that lasts starts with getting the assessment right before the work ever begins.

Our goal isn’t just to sell you a coating. It’s to recommend a system that makes sense for your floor.

07/15/2026

Kansas City doesn’t do mild.
Brutal summers, hard winters, and just enough random warm days in February to make concrete expand before temperatures drop and it contracts again. That constant back and forth of the freeze-thaw cycling, humidity swings, and temperature changes that can bring all four seasons in a single week puts real stress on concrete over time, and exterior surfaces take the worst of it.

That’s exactly why prep work isn’t something we rush or skip steps on. Every condition this climate creates in a slab like the cracking, surface breakdown, and moisture that has worked its way into the concrete has to be addressed before a coating ever goes down. Skipping that step in a market like KC isn’t a shortcut; it’s just a delayed failure.

Nineteen years in this market means we’ve installed floors through every season this city has thrown at us. We prep for the weather that’s coming, not just the floor we’re standing on.

What does the prep work actually consist of?Before a single drop of coating touches your floor, there’s a full process t...
07/14/2026

What does the prep work actually consist of?

Before a single drop of coating touches your floor, there’s a full process that has to happen first—and it’s the part most people never see.

We begin by inspecting the concrete and protecting the surrounding space. Plastic sheeting goes over doors, cabinets, belongings, and anything else that needs to stay clean. Equipment only comes in once the space is protected and the work area is ready.

From there, we diamond-grind the main field of the floor to remove weak surface material, old coatings, and surface contaminants while opening the concrete to create the proper profile for the new system to bond to. The perimeter is then edge-ground separately so nothing gets missed along walls, corners, doorways, and other tight areas the larger grinder cannot reach. Cracks, divots, spalled areas, and other damaged sections are repaired as needed and ground flush with the surrounding concrete. Those repairs are not just cosmetic—they help create a sound, even surface before the coating system is installed.

Once the grinding and repairs are complete, the floor is thoroughly vacuumed and cleaned. Every bit of concrete dust, loose material, and grinding residue has to be removed because anything left behind can interfere with the bond. The edges are then masked cleanly, the mix station is set up, and every roller, squeegee, bucket, and material is staged before we ever open a coating kit.

That sequence isn’t optional, and it isn’t negotiable. Every step exists because skipping one creates a problem downstream. After 19 years and more than 2 million square feet installed, we’ve seen exactly what happens when prep gets rushed.

The coating is the part you see. The prep is the part that makes it last.

What is Graniflex?Most coating systems are engineered for concrete that's in reasonably good condition. Graniflex was en...
07/14/2026

What is Graniflex?

Most coating systems are engineered for concrete that's in reasonably good condition. Graniflex was engineered for everything else. It's a rubberized waterproof membrane system built specifically for concrete that's heavily cracked, deteriorating, or battling moisture. The surfaces that would destroy a standard coating within a season or two. Pool decks, patios, driveways, porches, garage floors, and basement floors that have been written off as "too far gone" are exactly where this system earns its reputation.

Here's what separates it technically: Graniflex isn't just applied on top of the concrete, it penetrates up to 1.5 inches into the slab itself, where the rubber membrane cures as tough as a truck tire inside the concrete. Those rubber-like fingers expand and lock into the capillaries of the concrete, which is how it holds back extreme negative hydrostatic pressure. The kind of upward moisture force that lifts and destroys rigid coatings from underneath. It's rated to stretch 590% before failure, it never hardens or becomes brittle with age, and because of its Elongation Memory technology, it returns to its original shape after compression, so freeze-thaw cycles, ground movement, and vibration don't break the bond the way they would with a standard epoxy or polyaspartic system. Once it's down, it cannot bubble, peel, or delaminate.

The finished surface looks identical to our Full Flake System, a full broadcast of decorative vinyl flakes locked under a protective polyaspartic top coat, in hundreds of color combinations. You get a floor that looks like a high-end garage coating and performs like a waterproof rubber membrane built into the slab itself.

Metallic epoxy floors are surprisingly easy to maintain. For routine cleaning, use a microfiber mop with water and a sma...
07/11/2026

Metallic epoxy floors are surprisingly easy to maintain. For routine cleaning, use a microfiber mop with water and a small amount of dish soap. Water and white vinegar also work well for lighter cleaning, and spills should be cleaned promptly to prevent residue and buildup.

A little prevention goes a long way, too. Place furniture pads under chair and stool legs, and lift sharp or metal-edged items instead of dragging them across the floor. Wheeled chairs and equipment may create visible wear patterns in frequently traveled areas over time.

That’s really it. Metallic epoxy delivers a high-impact finish without demanding a complicated maintenance routine.

07/11/2026

Our Design Process:

Metallic epoxy isn't just a "pick a color or two off a chart" kind of system, it's closer to a custom art piece. We sit down with clients to talk through color combinations, the mood they want for the space, and how much movement/pattern they're after, then walk through sample boards and photos so there are no surprises on install day. Because the pigment moves naturally during application, we're always upfront that some variation from the sample is part of what makes it unique, not a flaw.

Setting that expectation early is something 19 years in this business has taught us matters just as much as the install itself.

Every metallic floor we install is genuinely one of a kind, even using the same color palette twice won't produce the sa...
07/08/2026

Every metallic floor we install is genuinely one of a kind, even using the same color palette twice won't produce the same pattern. This floor shows off that high-gloss, almost liquid-glass look that metallic epoxy is known for, with color movement you really have to see in person to appreciate fully.

If you're picturing something like this for a basement, office, or showroom, let's talk through color options.

"Epoxy" Isn't Just One ThingA lot of confusion in this industry comes from "epoxy" being used as a blanket term, when in...
07/08/2026

"Epoxy" Isn't Just One Thing

A lot of confusion in this industry comes from "epoxy" being used as a blanket term, when in reality it can be one component or a finished system. The applications and finished appearance vary dramatically depending on what's actually being installed, a flake system, a metallic epoxy, or a warehouse-grade epoxy engineered for serious chemical resistance are three very different floors.

Even within those, the epoxy itself isn't one product. Macro epoxy, slow-flow epoxy, high-flow epoxy, moisture v***r membranes. Each is formulated for a different surface condition or use case, and choosing the wrong can lead to floors failing prematurely or being upset that you thought you were getting one thing but recieved another. Asking for "an epoxy floor" is a bit like asking for "a car". Technically accurate, but it doesn't tell you much about what you're actually getting. That's exactly why the estimate and consultation phase of every project matters as much as it does. It's where we figure out which version of "epoxy" actually fits your space, your use case, and your budget.

And epoxy is really just one branch of what's possible. Overlays, polished concrete, and polyaspartic systems all solve different problems in their own way, sitting entirely outside the epoxy category altogether.

How is the Marbled/Depth Effect Is Actually Created?Metallic epoxy is one of the most fun systems we install, mostly bec...
07/07/2026

How is the Marbled/Depth Effect Is Actually Created?

Metallic epoxy is one of the most fun systems we install, mostly because no two floors ever come out the same. Metallic pigments are mixed into the epoxy and then manipulated while it's still wet using our rollers and squeege to push the pigment into swirls, veins, and pooling patterns that create real depth and movement. It's part science, part art, and a lot of practiced hands.

The result is a floor that looks almost three-dimensional, with color shifting depending on the angle and light hitting it.

Address

Kansas City, MO

Opening Hours

Monday 7:30am - 5:30pm
Tuesday 7:30am - 5:30pm
Wednesday 7:30am - 5:30pm
Thursday 7:30am - 5:30pm
Friday 7:30am - 5:30pm

Website

Alerts

Be the first to know and let us send you an email when KC Artistic Concrete posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to KC Artistic Concrete:

Shortcuts

Share

Category